A complete precision-tooling portfolio — Rotary Dies, Magnetic Cylinders, Pinnacle Tools, Progressive Tools, Flatbed Dies, NC-Machined Dies, Anvils & Sleeves, Hot-Stamping Tools, Embossing Dies, and Specialized Coatings. Engineered to specification. Manufactured to micron tolerance. Shipped on schedule.
The ToolWerz Standard.
Engineered Tooling Families
From rotary and flatbed dies to specialty cavity tooling, drive shafts, custom fixtures, and die-cut foam — every family is engineered, ground, and finished in-house to repeatable, press-rated specification.
Rotary Dies
Cylindrical- Solid Rotary — Single-piece engraved cylinder. Built for long-run, high-precision, abrasive applications.
- Flexible Magnetic — Engraved plate mounted to a magnetic cylinder. Rapid changeover, lower upfront cost.
- Segmented — Modular sections for easy handling, storage, and worn-part replacement.
Flatbed Dies
Flat- Steel Rule — Hardened steel rule strips set into a laser-cut wooden base. Most common, cost-effective.
- Engraved/Etched — Single-piece machined steel. Intricate, high-tolerance, small-part work.
- Male/Female Hard Tool — Two-part matched metal die. High-volume, precision, long tool life.
Specialized Dies
Functional- Kiss Cutting — Cuts through top layer only, leaving the backing intact.
- Scoring & Creasing — Crease lines for paperboard folding without cutting through the material.
- Perforation — Series of fine holes for clean tear-off and controlled separation.
- Embossing — Raised or recessed surface texture for branding and tactile detail.
Shafts & Rollers
Drive + Accessory- Rotary Shaft — Solid drive shaft that mounts and powers tooling on the press.
- Magnetic Shaft — Embedded-magnet shaft that holds flexible dies in position.
- Air Shaft — Pneumatic lug or leaf shaft for material-roll mounting and tension control.
- Accessory Rollers — Precision-ground idlers, nips, and dancers for material guidance.
Jigs & Fixture
Custom- Holding Fixtures — Locate and clamp parts during machining or assembly.
- Drilling Jigs — Guide drilling operations for repeatable hole patterns.
- Inspection Fixtures — Measure and verify part conformance to spec.
Tooling Foam
Sponge Rubber- Open-Cell Foam — Soft, breathable. Cushioning, sound dampening, filtration.
- Closed-Cell Foam — Water and dust resistant. Gaskets, weatherseals, flotation.
- Specialty Elastomers — EPDM, neoprene, and silicone for high-temp, oil-rated, and clean-room applications.
Coatings That Outlast Standard Tooling
Two specialized surface treatments engineered to extend tool life, eliminate adhesive build-up, and reduce total cost of ownership across every die family.
Anti Adhesion Coating
A specialized low-friction coating that prevents adhesive residue, inks, and substrate material from bonding to the tooling surface.
- Prevents adhesive and ink transfer to die surfaces.
- Dramatically reduces cleaning downtime between jobs.
- Maintains consistent cut quality on sticky substrates.
- Improves production throughput and reduces waste rates.
Hardness Enhancement
A hardness-enhancing surface treatment that significantly extends operational life across rotary, flatbed, and cutting tools.
- Extended tool life vs. uncoated tooling.
- Maintains sharp cutting edges through millions of strokes.
- Reduces frequency of die replacement and re-sharpening.
- Reduces cost and shortens production lead time.
From Drawing to Delivered Tool — In Five Steps
Every project flows through five disciplined stages — from first sketch to commissioned tool, with engineering, manufacturing, and inspection rigour at each gate.
Drawing or Concept
RFQ, sketch, or drawing received and reviewed.
Engineering Review
Manufacturability and tooling spec analysis.
Manufacture
CNC, grinding, etching, and optional coating.
Inspection
CMM, optical, and profilometry verification.
Delivery
Commissioned, documented, and supported.
Precision Converting at Line Speed.
Engraved, ground, and inspected in-house. Built to run.
